Hach SC1000 User Manual Page 67
- Page / 150
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
65
Standard Operations
5 Hardware error Hardware error detected.
6 Internal communication error
A communication failure within the device has been
detected.
7 Humidity error Excessive humidity has been detected.
8 Temperature error Temperature within the device exceeds specified limit.
10 Sample warning Some action is required with the sample system.
11 Questionable calibration warning The last calibration was of questionable accuracy.
12 Questionable measurement warning
One or more of the measurements of the device are of
questionable accuracy (Quality bad or out of range).
13 Safety warning
A condition has been detected which may result in a
safety hazard.
14 Reagent warning Some action is required with the reagent system.
15 Maintenance required warning Maintenance is required on this device.
Table 15 Error register
Bit Error Description
Table 16 Status register—Status 1
Bit Status 1 Description
0 Calibration in progress
The device is in calibration mode. The measurements
may not be valid.
1 Cleaning in progress
The device is in cleaning mode. The measurements may
not be valid.
2 Service/Maintenance menu
The device is in service or maintenance mode. The
measurements may not be valid.
3 Common error
Device recognized an error, see Table 15 for more
detailed information
4 Measurement 0 Quality bad Precision of measurement is out of specified limits.
5 Measurement low limit Measurement is below specified range.
6 Measurement high limit Measurement is above specified range.
7 Measurement 1Quality bad Measurement is below specified range.
8 Measurement 1 low limit Measurement is above specified range.
9 Measurement 1 high limit Measurement is below specified range.
10 Measurement 2 Quality bad Measurement is above specified range.
11 Measurement 2 low limit Measurement is below specified range.
12 Measurement 2 high limit Measurement is above specified range.
13 Measurement 3 Quality bad Measurement is below specified range.
14 Measurement 3 low limit Measurement is above specified range.
15 Measurement 3 high limit Measurement is below specified range.
- USER MANUAL 1
- April 2008, Edition 1 1
- Table of Contents 3
- Section 1 Specifications 7
- Specifications 10
- Section 2 General Information 11
- 2.3 Controller storage 12
- Section 3 Installation 13
- Installation 14
- 3.1.1 Controller dimensions 14
- 3.2 Mounting the controller 15
- 3.3 Wiring safety information 16
- 3.4 Electrical installation 18
- 3.6 Expansion cards 29
- 3.6.1 Relay card connections 30
- 3.6.2 Input card connections 33
- 3.6.3 Output card connections 35
- 3.6.4 Modbus card connections 36
- 3.8.2 Add probe connections 46
- 3.10 GSM modem connection 47
- 3.10.2 SIM card requirements 48
- 3.11 Storage card (SD card) 51
- Section 4 System Start Up 53
- System Start Up 54
- Section 5 Standard Operations 55
- Standard Operations 56
- 5.1.3 The display modes 56
- 5.3 The Graph display 58
- 5.4 The Main menu display 60
- 5.5 The alphanumeric keypad 61
- 5.8 Set the time and date 62
- 5.10 Add and remove favorites 63
- 5.11 Add new components 63
- 5.13 Remote control 69
- 5.14 Log data 73
- 5.15.1 Add a formula 75
- 5.15.3 Formula operations 76
- Section 6 Advanced Operations 79
- 6.3 System setup menu 80
- 6.3.2 Current inputs menu 85
- 6.3.3 Relay menu 89
- Advanced Operations 100
- 6.3.5 GSM module 115
- 6.3.6 Device management 117
- 6.3.7 Display settings 117
- 6.3.9 Storage card 118
- 6.3.8 Browser access 118
- 6.4 Test/Maint Menu 119
- 6.4.1 Bus status 120
- Section 7 Maintenance 121
- Maintenance 122
- Section 8 Troubleshooting 123
- 8.2 GSM Module errors 124
- Troubleshooting 125
- 8.3.2 Message format 125
- 8.4 SMS service 126
- 8.5.1 Test the output card 128
- 8.5.2 Test the input card 129
- 8.5.3 Test the relay card 130
- 9.1 Expansion cards 131
- 9.2 External DIN rail modules 131
- 9.4 Accessories 131
- 9.5 Replacement parts 132
- 9.4 Accessories (continued) 132
- 9.6 Exploded view drawings 134
- Figure 72 Display module 137
- Contact Information 140
- Section 11 Certification 141
- Certification 142
- A.1 Mount the DIN rail 143
- A.3 Attach the base module 144
- A.7 Dismantle the DIN rail 149
© 2020, manymanuals.com. All rights reserved. | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals